MORNING STAR OBSERVATORY
  • Home
    • About
    • Contact
  • Astrophotography
  • The Observatory
    • The New Observatory
    • - About the ExploraDome
    • - About the Lancaster Dome
    • - Building the Lancaster Dome
  • Equipment
    • CCD Cameras >
      • Orion Starshoot Pro
      • QSI 683WS
      • ZWO ASI-178MM
    • Eyepieces
    • Filters
    • Mounts >
      • Orion HDX-110 (EQ-8) >
        • New HDX-110 Setup
        • Orion HDX110 EQ-8
    • Observatory Computers
    • Telescopes >
      • Astro-Tech AT6RC
      • Celestron C-11 XLT
      • Zhumell 152mm Refractor
  • Projects
    • Arduino Focuser
    • C11 XLT Mods
    • Orion SSPRO Camera >
      • Disassembled Views
      • Noise Reduction Mod
      • Temp Controller Mod
    • Ultima 8 Mods
    • Zhumell Refractor Mods
  • Non-Astronomy
    • Amateur Radio >
      • Boat Anchor Radios >
        • BC-348N Receiver
        • Collins 51J4 HF Receiver
        • R-392 HF Receiver
      • DIY >
        • Station Boom Microphone
      • Ameco >
        • Ameco AC-1
        • Ameco OCM
        • Ameco PT-2
        • Ameco R5A
      • Heathkit >
        • Heathkit SB-102 Station
      • Knight-Kit >
        • Knight Kit Span Master II
      • Yaesu FT-817 >
        • Yaesu FT-817ND
        • LDG Z-817 Autotuner
        • Windcamp LiPo Battery
    • Antique Radios >
      • Building A Radio Workbench
      • Radio Dial Neon Clock
      • Radios >
        • 1938 Zenith 6-S-254
        • Echophone EC-1
        • Eltz Radione 2
        • Panasonic RF-5000A
        • Silvertone Model 4465
    • Geiger Counters >
      • AN/PDR-27G Radiac Set
      • Lionel CD V-700 Geiger Counter
      • RCA WF-12A Geiger Counter
    • Test Equipment >
      • DIY Test Equipment >
        • DIY Curve Tracer
        • DIY Signature Tracer
      • Military Test Equipment >
        • BC-221-AF Frequency Meter
        • LM-21 Frequency Meter
        • TS-323/UR Frequency Meter
        • TS-465 C/U Sweep Generator
        • TS-505D/U VTVM
        • TV-3C/U Tube Tester
      • Tube Testers >
        • Alternating Current Sink
        • Drug Store Tester
        • EMC Model 200 Tube Tester
        • Hickok Model 6000A Tube Tester
        • Hickok OZ-1 (550X)
        • Precise Model 111 Tube Tester
        • Precision Model 10-12
        • Supreme Model 385
        • TV-3C/U Tube Tester
      • VTVMs and Multimeters >
        • B&K Model 290 Hi-Low FET Multimeter
        • Hickok 225K VTVM
        • McMurdo Silver VOMAX 900
        • Micronta 22-220 FET Multimeter
        • Simpson 360-2 Digital FET DMM
        • TS-505D/U VTVM
      • Hickok >
        • Hickok 19X RF Generator
        • Hickok 225K VTVM
        • Hickok 288X RF Generator
        • Hickok OZ-1 (550X)
        • Hickok 6000A Tube Tester
      • Simpson >
        • Simpson 360 DMM
        • Simpson 360-2 DMM
        • Simpson 480 Genescope
      • Supreme Instruments >
        • Supreme 385 Automatic
        • Supreme 560 Vedolyzer
        • Supreme 560A Vedolyzer
        • Supreme Model 561 AF/RF Generator
        • Supreme's Model 562 Audolyzer
        • Supreme Model 562 Audolyzer circa 1941
        • Supreme Model 562 Audolyzer circa 1946
        • Supreme Model 563 Audio Generator
        • Supreme Model 576 RF Generator
      • Other Test Equipment >
        • Heathkit IT-28 Capacitor Tester
        • Rider 162 Chanalyst
        • Tektronix 326 O'scope
        • VU-Data Model 941B Oscilloscope
    • ---------------
    • Fossils
    • Rocks and Minerals
    • Star Trek >
      • Star Trek Rock Mood Lamp
      • Star Trek Communicator

Restoring a TS-505D/U Vacuum Tube Voltmeter

This TS-505 "D" model dates to around 1958. It's a ruggedized vacuum tube voltmeter that can measure DC voltages from .05V to 1000V, AC voltages from .05V to 250V at frequencies from 30Hz to 1MHz, and resistance from 1 to 1000MΩ (1GΩ). And using the MX-1797/U RF adapter on the DC probe, it can measure voltages from .05V to 40V at frequencies from 500KHz to 500MHz.

The D model is arguably the best model of the TS-505. It is the only version that doesn't pose a shock hazard when measuring higher voltages. This is because it has an isolated common that is not connected to the metal body of the meter, unlike the other four versions.

I picked up my first TS-505D back in the '70's, but don't have it anymore, so when I saw this one for sale, nostalgia took over and here it is on the bench.

Picture
Picture
On the outside this one is a bit rough, but with a good cleaning and a new paint job it won't look like the same instrument.

The handle is bent and some of its mounting hardware is missing. The meter is sitting upside down in the photo because the handle is stuck around the bottom. This will all get fixed when the case is disassembled for painting.

Picture
The face is dirty and there's paint chipped off around the storage compartments on each side of the meter movement. All the probes are there except the one for ACV. When I bought this I thought there was mold growing on the rubber gaskets, but it turned out to be sawdust of all things.

​The insulation is cracked on the black and green test leads and there's bare wire where they enter the meter, so I'll be installing all new leads. The shielded cable for the DCV probe is stiff and needs replaced. Also, the power cord is so stiff it cracks just trying to unfold it, so it will have to be replaced.

The storage compartments are scratched and dirty and will need repainted in addition to touching up the chipped edges.

Picture
There is an old certification seal on the side where the face and body join and if I'm reading it right, it looks like it was last calibrated 10-65. The label was still intact so this meter hasn't been opened up since then.

Picture
There's a schematic for the meter in the back of the case. Vintage military equipment is good about having a schematic inside. And best of all, it's still in nice condition.

Picture
The electronics are clean thanks to the sealed case. A few of the tube shields had a little oxidation that cleaned off easily, and there was some white rust on a couple of zinc plated parts. But that brushed off easily too.

I see several .01uf micamold-style capacitors that I'll need to check to see if they are paper. And I want to check the two 0.5uf filter caps to see what they're made of, too.

Picture
The face has been repainted from the top down to the center line of the meter movement. The two compartments either side of the meter have also been repainted. The meter bezel and the rest of the panel below it have been cleaned, but still need the paint touched up.

​A new line cord has been installed and I'm just getting started replacing the test leads.

Picture
The probes have been installed on new leads and the leads just need to be soldered in on the meter side. The red DC probe has a 5MΩ, 1% resistor inside that was out of tolerance and was replaced. It's the only component I've replaced so far.

Picture
It's a good thing I started checking capacitors, because I sure found enough bad ones. These two .01uf Micamold capacitors, that I had noticed earlier, are paper and foil just as I suspected. The larger one is marked as a type 345. It failed the leakage test on my cap tester at 3 volts.

Picture
Here's another of the Micamold .01uf caps and it's bad too. And the big, rectangular can behind it is one of the two 0.5uf power supply filter capacitors. They have a 1958 date code and both of these are very leaky too, and failed the leakage test on my IT-28 at 3 Volts. That pretty much makes them a short. Good thing I didn't power up the meter before testing them.

Picture
There's not much room for replacements, but I found just enough space to mount the new 0.5uf caps against the side wall and still leave the original caps installed for originality. They are oil-filled caps and might contain PCBs, so I'm not opening them to install the new caps inside.

​I changed the terminal strip to get an extra mounting lug and I soldered an insulated turret terminal to one of the old 0.5uf capacitor lugs to get another mounting point. Since I pulled the 3300Ω resistor when I removed the old terminal strip, I went ahead and replaced it with a new metal film resistor, even though it was still in spec.

Picture
I think this is the last capacitor to replace. It's a 100uf 15 volt electrolytic. It's right in the middle of the chassis with a resistor and a selenium rectifier mounted on top of it. Somewhere I read a comment about the TS-505 meters not having any electrolytics in them, but it ain't so. At least there's one in the D model. Since this bathtub cap isn't oil filled, I cut the back open, replaced the capacitor inside, and then soldered it shut again. Normally I wouldn't solder the can closed again, but it mounts upside down so the open bottom was visible.
After replacing the capacitors I brought the meter up on my variac, but it was completely dead. After a big "uh-oh" I made a couple quick checks with an ohmmeter and it turned out the On/Off switch contacts were dirty. The switch was pulled and cleaned with Deoxit and now it works. Initial tests look good so next is a calibration.

Picture
Picture
The front panel painting and touchup is done. In addition to touching up the gray paint, some of the black and green labeling needed fixed, too. It looks pretty good now.

The calibration went smoothly, straight by the manual, with one exception. When I calibrated the AC, the cal potentiometer was at its minimum. On the schematic the AC Cal pot is shown in series with a 500Ω resistor R9. But R9 in this unit is 1500Ω and it's listed as the same in the parts list. I changed R9 to 500Ω, but all that did was put the cal pot at maximum resistance, so I put it back to 1500Ω. The depot manual advises to check the range resistors R21 - R27 & R29. They were all on the high side of their nominal values, but were still within 1%. I guess all the resistors being a little high has resulted in enough of a cumulative error to shift the cal pot all the way to the end.
​
To get the cal pot to the center of its range, the pot and R9 need to have a combined range of 1KΩ to 2KΩ. To get this range I paralleled R9 with a 2200Ω resistor. Now the AC calibrates with the pot about in the center.

Picture
Picture
The case is now all cleaned up and repainted. I masked off the original stenciling and saved it. I used nylon washers, and plastic washers that I made, to replace the missing pieces for attaching the handle.

All the meter ranges are pretty spot on. I especially like the RX1M scale, it will be useful for leakage testing, and the ohmmeter reads accurately all across the scale.

Page created 10/25/2020
​Last edit 10/31/2020
Powered by Create your own unique website with customizable templates.
  • Home
    • About
    • Contact
  • Astrophotography
  • The Observatory
    • The New Observatory
    • - About the ExploraDome
    • - About the Lancaster Dome
    • - Building the Lancaster Dome
  • Equipment
    • CCD Cameras >
      • Orion Starshoot Pro
      • QSI 683WS
      • ZWO ASI-178MM
    • Eyepieces
    • Filters
    • Mounts >
      • Orion HDX-110 (EQ-8) >
        • New HDX-110 Setup
        • Orion HDX110 EQ-8
    • Observatory Computers
    • Telescopes >
      • Astro-Tech AT6RC
      • Celestron C-11 XLT
      • Zhumell 152mm Refractor
  • Projects
    • Arduino Focuser
    • C11 XLT Mods
    • Orion SSPRO Camera >
      • Disassembled Views
      • Noise Reduction Mod
      • Temp Controller Mod
    • Ultima 8 Mods
    • Zhumell Refractor Mods
  • Non-Astronomy
    • Amateur Radio >
      • Boat Anchor Radios >
        • BC-348N Receiver
        • Collins 51J4 HF Receiver
        • R-392 HF Receiver
      • DIY >
        • Station Boom Microphone
      • Ameco >
        • Ameco AC-1
        • Ameco OCM
        • Ameco PT-2
        • Ameco R5A
      • Heathkit >
        • Heathkit SB-102 Station
      • Knight-Kit >
        • Knight Kit Span Master II
      • Yaesu FT-817 >
        • Yaesu FT-817ND
        • LDG Z-817 Autotuner
        • Windcamp LiPo Battery
    • Antique Radios >
      • Building A Radio Workbench
      • Radio Dial Neon Clock
      • Radios >
        • 1938 Zenith 6-S-254
        • Echophone EC-1
        • Eltz Radione 2
        • Panasonic RF-5000A
        • Silvertone Model 4465
    • Geiger Counters >
      • AN/PDR-27G Radiac Set
      • Lionel CD V-700 Geiger Counter
      • RCA WF-12A Geiger Counter
    • Test Equipment >
      • DIY Test Equipment >
        • DIY Curve Tracer
        • DIY Signature Tracer
      • Military Test Equipment >
        • BC-221-AF Frequency Meter
        • LM-21 Frequency Meter
        • TS-323/UR Frequency Meter
        • TS-465 C/U Sweep Generator
        • TS-505D/U VTVM
        • TV-3C/U Tube Tester
      • Tube Testers >
        • Alternating Current Sink
        • Drug Store Tester
        • EMC Model 200 Tube Tester
        • Hickok Model 6000A Tube Tester
        • Hickok OZ-1 (550X)
        • Precise Model 111 Tube Tester
        • Precision Model 10-12
        • Supreme Model 385
        • TV-3C/U Tube Tester
      • VTVMs and Multimeters >
        • B&K Model 290 Hi-Low FET Multimeter
        • Hickok 225K VTVM
        • McMurdo Silver VOMAX 900
        • Micronta 22-220 FET Multimeter
        • Simpson 360-2 Digital FET DMM
        • TS-505D/U VTVM
      • Hickok >
        • Hickok 19X RF Generator
        • Hickok 225K VTVM
        • Hickok 288X RF Generator
        • Hickok OZ-1 (550X)
        • Hickok 6000A Tube Tester
      • Simpson >
        • Simpson 360 DMM
        • Simpson 360-2 DMM
        • Simpson 480 Genescope
      • Supreme Instruments >
        • Supreme 385 Automatic
        • Supreme 560 Vedolyzer
        • Supreme 560A Vedolyzer
        • Supreme Model 561 AF/RF Generator
        • Supreme's Model 562 Audolyzer
        • Supreme Model 562 Audolyzer circa 1941
        • Supreme Model 562 Audolyzer circa 1946
        • Supreme Model 563 Audio Generator
        • Supreme Model 576 RF Generator
      • Other Test Equipment >
        • Heathkit IT-28 Capacitor Tester
        • Rider 162 Chanalyst
        • Tektronix 326 O'scope
        • VU-Data Model 941B Oscilloscope
    • ---------------
    • Fossils
    • Rocks and Minerals
    • Star Trek >
      • Star Trek Rock Mood Lamp
      • Star Trek Communicator